Setting up:

• One appliance per power outlet.  
• Make sure you have place the machine under a cover away from the hot sun and the wind.
  
• Place machine on a sturdy table (coffee table size). 
  
• Fit bowl around collar and place bubble around the lip of the bowl.  
   
• Make sure both switches are off (in the up position). 
  
• Fill the head with sugar while the machine is off. 
  
• Connect the lead to the machine and power point. 
  
• Turn on both switches and turn the heat control to 5 (clockwise is up).  It will take about 4-5 minutes to heat up.  Get familiar with the heat control because this is the control which you turn up to make the machine faster, and down to slow it down.  You have complete control of the machine so use the control to get the speed that suits you best.

Making a stick of floss:

Place you stick inside the bowl, twist the stick in your fingers and also move in an anti-clockwise direction.  Don't roll the stick of floss along the side of the bowl, you will pick-up the waste which isn't soft and fluffy and make the flossy heavy.  Make sure you have the stick low to the bottom of the bowl so that the fairy floss grips the stick well.  Make it to the size you want.  Refill the sugar in the head every 5-6 sticks (while the machine is running).  If you don't refill the head often then the machine will get too hot and floss will go thick like rope and burn.

Cleaning the machine:

When finished for the day, turn the floss control to off.  Turn off the heat switch then let the motor run for about 2 minutes to cool the head of the machine down.  Now once cooled switch off machine motor and remove power lead from the machine.

Lift off the bowl and bubble from the machine and then wash the bowl and bubble with warm water and a mild detergent.  No harsh rubbing or chemicals!  Warm soapy water will dissolve the waste. 

Warning:  you can wipe over the cabinet and neck of the machine with a damp cloth  but do not wash or touch the head of the machine.  There is an electrical element in the head of the machine which should never come in contact with water.  

(WARNING: The cost of replacing an element in the head of a fairy floss machines is $250.00).

If in difficulty at any stage please phone our office on (03) 9878 4002 or mobile no. 0421 723184.  Never attempt to repair the machine.  It is most likely a minor problem with a simple solution.

Setting Up:

• One appliance per power outlet.
• Place machine under a Marquee.
• Place machine on a sturdy table.
• Connect the lead of the machine to the power point.
• Flick the heat switch on to warm up the cabinet.

Popping Popcorn

Turn the 'kettle' switch and the 'turn' switch on. Let the kettle warm up for about 1 minute and then add the popping oil.  Let the oil melt for about  20-30 seconds and then add the corn kernels.  Now sprinkle the butter salt over the kernels and lower the lid and wait for it to start popping.  It will take about 3 minutes.  Listen to the kernels pop and when the pops seem to be slowing down to every few seconds then turn off the 'kettle' switch and the 'turn' switch.  Lift up the lid, turn the kettle handle to the number '9' position on a clock and empty the kettle completely.  Let the handle move back into the normal position and then gently reposition the kettle for the next pop.  Note:  don't leave the kettle on or it may burn your popcorn...

Repeat these steps for each pop.

Cleaning

make sure all switches are in the off position.  Disconnect the power cord, then scoop out remaining popcorn.  Remove the waste tray at the bottom of the machine and discard popcorn waste before replacing the waste tray.  Wipe out the inside of the cabinet and the inside of the kettle with towelling paper to remove any oil and popcorn waste.  wipe the accessories and the waste tray and place back inside the unit. 

 warning:  do not disassemble the unit or wash the machine. .this is done by us on return. (warning:  popcorn kettles cost  $200.00 to replace)  .

if in difficulty at any stage please phone our office on (03) 9878 4002 or
mobile no. 0421 723 184.  never attempt to repair the machine.

Snowcone Ice Shaving Machine instructions

Setting up:

• One appliance per power outlet.
• Place machine on a sturdy table.
• Make sure the machine and light is switched off before you plug in the unit.
• Connect the lead from the machine to the power point. 
• Make sure the motor switch is turned off at all times except when your are shaving ice.

Shaving Ice:

It is extremely important to note that these machines best operate when the ice is pulled directly out of the freezer.  Turn on the shaver before you start adding ice.  Lift up ice pusher to rest position and then drop ice into shaver followed by pusher arm (use a pumping action). Shaved ice will flow into the cabinet.  Finish shaving the bag of ice until you have a large pile of snow as this will attract customers.  Now turn the shaver off.

Scoop the snow into the cone and finish it by making a round ball with the ladle for the top.  Hand the cone to your assistant who will put on the syrup for the customer.  Don't forget to place a spoon straw in the cone when you are done.

WARNING:  Do not at any time put hands, fingers, screw drivers or any objects except ice in the shaving chute.

Cleaning the Machine:

Please tip out any syrups in squeeze bottles and rinse the squeeze bottles.  Rinse the accessories and return all equipment and accessories.

If in difficulty at any stage please phone our office on (03) 9878 4002 or
mobile no. 0421 723 184.  Never attempt to repair the machine yourself.

Electric Steamer instructions

• One appliance per power outlet.
• Connect power cord to a suitable power outlet.
• Make sure the cord does not come in contact with any hot surfaces when in use.
• Fill the Steamer with water stopping at least 50 mm above the element.
• Arrange food in the basket and place inside steamer, put the lid on.
• Open steam vent on the lid and turn the switch on.
• Turn the dial setting to full until the water is boiled (approx 30 mins).
• When the steam emerges from vent, turn dial to required setting and close vent.

Cleaning:

Turn power off, unplug and allow to cool before empting water.
The interior and exterior parts of the steamer can be wiped over with a damp cloth.  DO NOT IMMERSE IN WATER. The basket can be washed with warm soapy water.